81eaae1f51
Remove unused useDefault parameter.
5 years ago
769bb597ca
Add up and down arrows to DoubleSlider, to show that the right thumb is for presses and the left is for releases.
5 years ago
f7453a1600
Add an error check for invalid JSON when importing a configuration.
5 years ago
219f407246
Fix JSON ParseError exporting settings if custom settings have never been edited.
5 years ago
7c6b64c13e
Use CheckRunning to close SMXConfig before uninstalls too.
5 years ago
5508c42b10
Make the installer shut the application down (or ask the user to do it if it's a version before SMXConfigShutdown).
5 years ago
54003cd6a3
Add an SMXConfigShutdown event to allow the installer to close the application automatically.
5 years ago
f85058e499
Remove unused AllocConsole binding.
...
This doesn't cause problems since it's never called, but it's never called.
5 years ago
0f74ffb832
Try to work around some broken antiviruses causing WPF to not be able to save settings.
5 years ago
bd052f08ef
Use OnClick instead of Checked and Unchecked.
...
Checked and Unchecked are called at weird, unpredictable times by WPF, and saving
settings when they happen causes us to change the setting incorrectly. OnClick is
only called when the user actually changes the value and not when internal WPF stuff
sets it, so it doesn't have this problem.
5 years ago
bb3ee5a0c9
Only recreate sliders when the sensitivity tab is selected, rather than on every tab change.
5 years ago
7171330abd
Update the wording for the custom sensor dialog.
5 years ago
1014a26940
Fix the version label getting cut off.
5 years ago
102fe2f9f9
Make the platform lights slider update directly when dragged, so we can delay config updates.
...
This is just a safeguard to prevent hammering the EEPROM erase cycles. It also
makes the platform slider update more smoothly (previously it would only update
at a few FPS since it was using config changes).
5 years ago
48fe72af4a
Update the EnableCenterTopSensorCheckbox label.
5 years ago
dffe001bec
Tighten the high preset a bit.
5 years ago
d4c71941eb
Implement separate inner and outer threshold sliders, and a custom threshold slider.
5 years ago
18475afbf8
Change ThresholdSlider to a grid, to make things easier to position. StackPanel is too limited for this.
5 years ago
883d87779a
Add aux sensors.
5 years ago
3bb92a0b24
Fix the visible threshold sliders not updating when enabled panels are changed.
5 years ago
dbb4ecc530
Refactor the way threshold sliders are associated with sensors.
...
This makes it possible to have sliders that influence arbitrary sensors.
5 years ago
8620da2405
Refactor displaying threshold sliders.
...
Instead of having the sliders show and hide themselves, create the ones that are
active in MainWindow.
5 years ago
ae25ed327a
Fix AreUnifiedThresholdsSynced modifying config.
5 years ago
109cd1f6f6
Fix highlighting selected diagnostics buttons on P2.
5 years ago
bbb49b6ae4
Show a warning if the low FSR threshold is set too low.
5 years ago
37e5b445cd
Fix exporting load cell thresholds to JSON.
5 years ago
80b08dbe0c
Fix exception parsing empty JSON arrays.
5 years ago
63f7aa5beb
Adjust the high FSR preset.
...
The 100-112 thresholds are extremely low, and don't work for all play styles, since
with harder presses, the 100 low threshold may not be reached quickly enough, which
causes missed inputs. Raise the high preset thresholds to something more reasonable.
Users can still set the lower values in the advanced tab if it works for them.
This might be tuned further.
This won't affect users who are already set to the higher thresholds, since it'll
just act like custom thresholds. To update thresholds to the new values, click the
"High" preset button again.
5 years ago
12794762a8
Fix "light panels" getting stuck on if the controller is disconnected while the button is pressed.
5 years ago
0c19451d7d
Show the diagnostics mode dropdown by default.
5 years ago
1959a1eaa9
Hide the floor lighting button on older pads.
5 years ago
3d6a3008ae
Fix the center preset to match the firmware and the game.
5 years ago
6249359373
Add an option to enable the center panel top sensor.
5 years ago
27be716768
Add disabled combined thresholds.
5 years ago
9facc93548
8-bit FSR thresholds.
6 years ago
05f4100d98
Add support for importing/exporting FSR thresholds to disk.
6 years ago
6cc979b1dc
Implement the V5 config packet.
6 years ago
0184e46022
Make sure GetConfig returns a valid stub SMXConfig if the DLL isn't present.
6 years ago
00271c3e15
Rename iBadJumper to iWrongSensorJumper.
6 years ago
122cbe7b0d
FSR threshold tuning.
6 years ago
23ef413d91
Only show enabled panels in the diagnostics tab.
6 years ago
b25b363c96
FSR threshold tuning.
6 years ago
cce566624a
Improve minimizing to tray, and restore the existing instance if SMXConfig is launched when it's already minimized to the tray.
6 years ago
ded697cf4c
Add sensor icons.
6 years ago
1b01f53796
Add an option to enable or disable lighting on panels with no sensors.
6 years ago
f35f596cee
Update the config block with new fields.
6 years ago
ec061d4223
Refactor uploading animations to allow uploading automatically instead of having a separate upload button, and iron out some inconsistencies.
6 years ago
74f94c5bf5
Add panel test mode to the UI.
6 years ago
501b297c8f
Rename iBadSensorDIP -> iBadJumper.
6 years ago
990a6ba488
Fix refreshing the selected diags button.
6 years ago
Glenn Maynard